Guide · The Waterproof Company
How hail and UV wear out flat-roof membranes in Gauteng
Flat-roof membranes on the Highveld have a hard life: strong sun for most of the year, big daily temperature swings in winter, and summer storms that can bring hail. Flat roof membrane hail damage is easy to miss from the ground, and UV wear is slow, so both often go unnoticed until a ceiling stain appears. This guide explains how each one wears a membrane and what to look for before the storm season.
Request a quoteThe sun
What UV does to a membrane
Gauteng sits at high altitude, so the sun is strong, and an exposed flat roof receives it for most of the day. Ultraviolet light breaks down the surface of bitumen and many coatings over time. Exposed bitumen oxidises, hardens and loses its flexibility, and a network of fine surface cracks, sometimes called crazing or alligatoring, can develop.
That is why most exposed torch-on membranes are protected by a reflective coating, often silver or white, or by a mineral-chip cap sheet. Liquid systems on roofs are usually finished with a UV-resistant topcoat. These protective layers wear first. When they chalk, flake or wash off, the membrane underneath starts to age much faster.
Heat and daily temperature swings
A dark roof surface in full sun gets far hotter than the air, then cools quickly at night. In the dry Highveld winter, the difference between day and night is large. Every cycle makes the membrane and the slab underneath expand and contract, which works at laps, upstands and the edges around outlets and penetrations.
Over several seasons, that movement can open laps, pull membranes away from parapet walls and crack brittle coatings. A reflective topcoat helps here too, because a cooler roof moves less.
Different systems wear in different ways
A smooth torch-on membrane relies entirely on its reflective coating for UV protection, so the coating needs renewing on a regular cycle. A mineral-chip cap sheet carries its protection in the surface, but loses chips over time, especially where water flows or people walk. Liquid acrylic systems depend on their topcoat and on being applied at the full specified thickness; thin areas age first. Polyurethane and other elastomeric systems are generally tougher, but they still need the right topcoat if they are exposed to the sun. Knowing which system is on your roof tells you what to check.
Hail
How hail damages a flat-roof membrane
Hail strikes a flat roof almost straight on. On a membrane that is still flexible, small hail may only knock off some surface protection. Larger stones can bruise the membrane, crush the mineral chips into the bitumen, crack an aged surface or puncture thinner layers. Damage tends to be worse on membranes that UV has already made brittle, which is why the two problems are linked.
Hail also blocks outlets. Stones pile up in outlets and box gutters during a storm, water rises on the roof, and it reaches upstands and laps that normally stay dry. Leaks after a hailstorm are not always caused by the hail hitting the membrane; sometimes it is the water that could not drain away.
What to look for
Signs of wear and hail damage
- Reflective coating that is chalky, patchy or flaking, with black bitumen showing through.
- Fine surface cracking, or cracks across the membrane at slab joints.
- Laps that have opened or lifted at the edges.
- Membrane pulling away from parapets and upstands, or loose flashings over the top edge.
- Blisters and soft spots, which can mean water or vapour trapped underneath.
- Granules or chips collected in outlets, gutters and low spots.
- Dents, scuffs or small holes after a hailstorm, often in a scattered pattern.
- Ponding that remains a day or two after rain.
Only go onto a roof if it is safe to do so. Flat roofs can be fragile at the edges and slippery when wet, and many have no edge protection. Photographs from a window or a ladder at the edge are often enough to show whether a closer look is needed.
After a storm
What to do after hail
Clear blocked outlets as soon as it is safe, so the next storm can drain. Photograph the roof, the outlets and any ceiling stains before anything is moved or repaired, and note the date of the storm. If you intend to make an insurance claim, check with your insurer before repairs start; they may want to see the damage or receive a report.
A temporary patch can protect a punctured area for a short time, but it should be followed by a proper repair that bonds to the existing membrane and is compatible with it.
Before the season
Maintenance that extends a membrane’s life
Most of the damage described above is slowed by simple maintenance. Before the storms, usually by September or October, clear outlets, box gutters and leaf traps. Check the reflective coating and renew it when it has worn, following the system manufacturer’s guidance. Keep foot traffic, ladders and equipment off the membrane where possible, and protect it under solar mounts, air-conditioning units and geyser supports.
Small defects, such as an open lap or a lifted upstand, are much cheaper to repair early than after a season of water has travelled under the membrane.
Repair or replace
When a membrane needs replacing
Local repairs make sense when the membrane is generally flexible and well bonded, and the damage is limited to particular areas. When the membrane is brittle and cracked across the roof, blistered in many places, or holding water underneath, patching tends to chase leaks from one storm to the next. At that point the usual answer is to remove the failed layers and install a new system, with the outlets and upstands detailed properly. A site inspection is what decides between the two.
Next steps
Read more about flat roof waterproofing, or about hail and storm conditions on our waterproofing in Pretoria page. When you are ready, request a quote.
Request a waterproofing quote
Send your suburb, what is leaking and a few photos. We arrange a site visit and set out the work in a written quote.
Request a quote