Flat roof waterproofing in Pretoria and Johannesburg
Flat roof waterproofing is mostly about water that cannot get away fast enough. On flat and concrete roofs in Pretoria and Johannesburg, a Highveld storm can drop more rain in minutes than poor falls and small outlets can handle. The Waterproof Company looks at how the roof drains first, then proposes a torch-on or liquid system and sets it out in a written quote.
Request a quoteFalls and ponding
A flat roof is never perfectly flat. It needs a gentle slope, or fall, that carries water to the outlets. Where a slab has sagged, was cast without enough fall or has had screeds added over the years, water collects in shallow pools after rain.
Ponding keeps the membrane wet and hot, wears it faster and puts water against every lap for longer. Where ponding is significant, the scope may include building up the falls with a screed before any membrane is laid. A membrane on its own will not make water flow uphill.
Our guide on how hail and UV wear out flat-roof membranes explains what to check before the storm season.
Outlets and box-gutter linings
Outlets that sit even slightly above the surrounding membrane leave a ring of standing water. Outlets that are too small, or that block with leaves and hail, back water up against parapets and upstands. We check the size, level and condition of each outlet and how the membrane is dressed into it.
Box gutters behind parapets carry a lot of water in a storm. Lining a box gutter with torch-on or a liquid system is waterproofing work we do. Replacing guttering and downpipes is a roofing job.
Upstands, parapets and edges
Where the roof meets a wall or parapet, the membrane has to turn up the wall far enough to stay above standing water and be sealed or chased in at the top. Shrinkage, sun and movement pull poorly finished upstands away from the wall over time.
We also look at the top of parapet walls. Cracked plaster and failed copings let water into the wall from above, which then runs down behind the membrane and appears indoors some distance from the roof edge.
Torch-on or liquid on a flat roof
Torch-on waterproofing suits many concrete slabs, especially larger, simple areas where the rolls can be laid in long runs with consistent laps. A liquid rubber system is often the better fit on small roofs with many penetrations, around complex outlets, next to timber or other materials where a flame is a risk, and over some existing systems.
Sometimes the right answer is a combination: torch-on across the field of the roof and a liquid system at the awkward details. The choice is made on site. Our roof waterproofing page covers the wider picture.
Overlaying or stripping an existing system
If the existing membrane is still well bonded and dry underneath, a new layer can sometimes go over it after repairs. If it is blistered, lifting or holding water, it usually has to come off first, or the new system inherits the old problem. We test the existing layer before recommending either route, and the quote says which one is proposed.
Garage roofs, concrete slabs and roof terraces
Not every flat roof covers a whole house. Many Pretoria and Johannesburg properties have smaller concrete slabs that need the same care, and that often get less attention because they are out of sight. These are among the commonest flat roof waterproofing situations:
- Garage roofs: slabs over garages and carports, often with a single outlet or spout, where a blocked outlet quickly causes ponding and a leak onto the car or storage below.
- Concrete slabs over extensions: flat sections added to pitched-roof houses, where the junction with the older wall and the upstand along it are the usual weak points.
- Roof terraces: slabs used as outdoor living space, which need a membrane that suits foot traffic or sits under tiles or a protective finish.
- Slabs with equipment: geysers, solar mounts and air-conditioning units, whose supports and pipes all have to be detailed into the membrane.
Common questions
How do I know if my flat roof ponds?
Look at the roof, safely, the day after rain. Pools still standing, tide marks, silt rings and green growth in low spots all point to poor falls or blocked outlets.
Can the falls be corrected without a new roof?
Often, yes. A screed can be laid to build up the falls towards the outlets before the new membrane goes down. The slab itself usually stays as it is.
Is a reflective coat necessary?
On an exposed bitumen membrane, a reflective topcoat protects it from UV and heat. It is part of the system and should be named in the quote, along with how often it may need renewing.
What about water tanks and geyser stands?
Stands, pipes and supports are penetrations. They need to be detailed into the membrane, and sometimes lifted temporarily. Tell us what is on the roof when you enquire.
Related waterproofing services
Roof waterproofing
Membrane and liquid systems for concrete slabs and sound metal or tiled roofs, with the outlets and upstands detailed properly.
Roof waterproofing →Torch-on waterproofing
Heat-bonded bitumen membranes for slabs, parapets and box gutters, laid with sound laps and upstands.
Torch-on waterproofing →Liquid rubber waterproofing
Seamless liquid-applied systems for metal roofs, awkward details and places where a flame is not suitable.
Liquid rubber waterproofing →Flat roof waterproofing in Pretoria and Johannesburg
We carry out flat roof waterproofing for homes, complexes and business premises across both cities. See waterproofing in Pretoria and waterproofing in Johannesburg for local conditions, or check the service areas page for suburbs.
To get started, request a quote with your suburb, a short description and a few photos. We arrange a site visit and send a written scope before any work is agreed.
Request a waterproofing quote
Send your suburb, what is leaking and a few photos. We arrange a site visit and set out the work in a written quote.
Request a quote