Serving Pretoria & JohannesburgMembrane waterproofing · Written quotes after a site visit

Torch-on waterproofing in Pretoria and Johannesburg

Torch-on waterproofing is a modified-bitumen membrane supplied in rolls and bonded to the roof with a gas torch. It is one of the most common systems on concrete slabs and flat roofs in Pretoria and Johannesburg. The Waterproof Company installs torch-on to the manufacturer’s system requirements, with the preparation, laps and upstands set out in a written quote.

Request a quote

What torch-on is

Torch-on membranes are made from bitumen modified with polymers (often described as APP or SBS modified bitumen) on a reinforcing carrier. The underside is heated until it melts and bonds to a primed surface. Adjacent rolls overlap and are heat-welded at the laps.

Some systems use a single layer; others use an underlay and a cap sheet. Exposed membranes are usually finished with a reflective coating or come with a mineral surface to protect the bitumen from the sun.

Where torch-on belongs

Torch-on is well suited to concrete slabs and flat roofs, parapet roofs, some balconies under a protective finish, and box-gutter linings. It works best on larger, simple areas where rolls can be laid in long runs. See flat roof waterproofing for how falls and outlets affect the job.

Preparation comes first

A torch-on membrane is only as good as the surface it is bonded to. Preparation typically includes removing loose or failed material, repairing cracks and spalled concrete, dealing with ponding, making sure the surface is dry and clean, and applying a primer compatible with the membrane.

Rushed preparation is the most common reason a new membrane fails early. The quote should list the preparation steps, not only the membrane.

Laps, upstands and outlets

Every lap is a potential leak if it is too narrow or not fully bonded. Upstands need to rise far enough up walls and parapets and be sealed or chased in at the top. Outlets need the membrane dressed into them so water runs over the lap, not into it. These are the details we check on site and specify in writing.

Resealing versus a new system

If an existing torch-on roof is mostly sound, targeted repairs at laps and upstands plus a new reflective coat may be enough. If the membrane is brittle, blistered or holding water, patching usually only moves the leak. We test the existing system before recommending either route and explain the reasoning.

How long does torch-on waterproofing last?

There is no single answer, because how long torch-on waterproofing lasts depends far more on the job and the roof than on the product name. A few things make the biggest difference.

Preparation comes first. A membrane bonded to a clean, dry, primed and repaired surface stays put; one laid over dust, loose screed or damp concrete can blister and lift. Laps are next: every overlap must be wide enough and fully fused, because an open lap is where most torch-on leaks start.

Sun and water then do the slow work. UV hardens exposed bitumen, so the reflective or mineral surface that shields it matters. Ponding keeps the membrane wet and hot against the laps for days after a storm, and regular foot traffic, ladders and equipment scuff and puncture it.

Maintenance closes the gap. Renewing the reflective reseal coat every few years, as the manufacturer recommends for that product, and keeping outlets clear, protect the membrane underneath. The quote should name the product, so you can read its data sheet, and state any guarantee in writing.

Can new waterproofing go over old torch-on?

Sometimes, yes. Laying a new torch-on membrane over an old one can work well when the existing layer is sound: firmly bonded to the slab, dry underneath and free of soft spots. The old membrane is cleaned, repaired at any open laps or damaged areas, and primed so the new layer bonds to it, and the upstands and outlets are re-detailed rather than simply covered.

It is the wrong approach when the old system has failed. Blisters, trapped water, layers lifting at the edges or a surface that gives underfoot all mean the new membrane would be bonded to something that is already moving or wet. Several old layers on top of one another add weight, hide the condition of the slab and make outlets sit too low. In those cases the old material should be stripped back to a sound surface first.

We check the bond and moisture of the existing layer on site, and the written quote says whether the proposal is an overlay or a strip.

Where heat is not appropriate

An open flame is not suitable next to timber, some insulation, thatch, plastic fittings and certain existing coatings, or on some metal roofs. In those places a liquid rubber system or another cold-applied option is used instead, sometimes alongside torch-on on the rest of the roof. Our guide on torch-on or liquid rubber compares the two.

Common questions

How long does torch-on last?

It depends on the product, the preparation, sun exposure and maintenance such as renewing the reflective coat. The quote should name the product so you can read the manufacturer’s information, and state any guarantee that applies.

Can torch-on go over the old membrane?

Sometimes, if the old layer is well bonded and dry. If it is lifting or holding water it usually has to be removed first. We test it before recommending either route.

When is it a bad idea to torch a new membrane over the old one?

An overlay is a poor choice when the old membrane is blistered, lifting or holding water. In those cases the old layer usually has to be removed first, otherwise the new membrane can inherit the same problem. An overlay may suit only if the existing layer is well bonded and dry underneath. We test the old layer before recommending either route and explain the reasoning in the written scope. Whether a particular roof can be overlaid is decided on site, not from a photo alone.

Can you walk on a torch-on roof?

Light maintenance traffic is usually fine. For regular foot traffic, a protective finish or walkway is normally needed. Tell us how the roof is used.

Is torch-on safe near my house?

Torch-on is applied with an open flame, so it is planned with care around anything combustible. Where heat is not appropriate, we use a cold-applied liquid system instead.

Related waterproofing services

Roof waterproofing

Membrane and liquid systems for concrete slabs and sound metal or tiled roofs, with the outlets and upstands detailed properly.

Roof waterproofing →

Liquid rubber waterproofing

Seamless liquid-applied systems for metal roofs, awkward details and places where a flame is not suitable.

Liquid rubber waterproofing →

Torch-on waterproofing in Pretoria and Johannesburg

We carry out torch-on waterproofing for homes, complexes and business premises across both cities. See waterproofing in Pretoria and waterproofing in Johannesburg for local conditions, or check the service areas page for suburbs.

To get started, request a quote with your suburb, a short description and a few photos. We arrange a site visit and send a written scope before any work is agreed.

Request a waterproofing quote

Send your suburb, what is leaking and a few photos. We arrange a site visit and set out the work in a written quote.

Request a quote