Guide · The Waterproof Company
Swimming pool leaks: linings, tiles and waterproofing
Swimming pool leaks waste water and money, and can damage the ground around the pool. But not every falling water level is a leak, and not every leak is a waterproofing problem. This guide explains how to tell evaporation from a leak, where pools commonly lose water, and when a new lining or waterproofing system is the right repair.
Request a quoteFirst check
Is it a leak or evaporation?
On a hot, dry and windy Gauteng day, a pool can lose a noticeable amount of water to evaporation, and splashing and backwashing add to that. A falling level on its own does not prove a leak.
The bucket test is a simple way to check. Place a bucket on a pool step, fill it with pool water to the same level as the pool, and mark both levels. Leave the pump running on its normal schedule and compare after 24 hours, with no rain and no topping up. If the pool has dropped noticeably more than the bucket, it is likely to be leaking. Repeating the test with the pump switched off helps show whether the loss is in the plumbing.
Where pools leak
Common leak points
- Pipework and equipment: suction and return lines, the pump, the filter and the backwash valve.
- Fittings in the shell: the joint between the skimmer box and the shell, return inlets, lights and their conduits.
- The shell itself: structural cracks in concrete or gunite, often from ground movement.
- The finish: worn or delaminated marbelite, cracked fibreglass, or loose tiles and failed grout on tiled pools.
- The coping and bond beam: the joint between the coping and the shell, where water can get behind the finish.
Other signs of a leak
Some clues are outside the pool. Look for a patch of lawn or garden that stays wet or grows faster than the rest, cracks or sinking in the paving next to the pool, water near the pump and filter, or air bubbles in the return jets. If the pool has an automatic top-up valve, it can hide a leak for months; a water bill that rises for no other reason is worth investigating. Note where you see these signs, because they help narrow down whether the loss is in the shell, a fitting or the pipework.
Plumbing leaks are a different job
If the bucket test points to the pump-on period, or there is wet ground near the equipment or along a pipe route, the leak is probably in the plumbing. That is work for a pool plumber or leak-detection specialist, who can pressure-test the lines. Waterproofing the shell will not fix a leaking pipe, so it makes sense to rule plumbing out before paying for anything else.
Shell and finish
When waterproofing is the answer
Waterproofing is the right repair when water is escaping through the shell or its finish: cracks in the structure, a lining that has failed, or a tiled pool where the waterproofing under the tiles is no longer intact. A dye test, where a little coloured dye is released next to a suspected crack or fitting in still water, can show whether water is being drawn out at that point.
The usual sequence is to drain the pool safely, prepare the surface, open up and repair cracks, seal fittings such as skimmer boxes and returns, and apply a waterproofing system that is designed for permanent immersion. The finish, whether marbelite, a pool paint system, fibreglass or tiles, then goes back over the top, compatible with the waterproofing beneath it.
A warning
Do not empty a pool without advice
An empty pool can be pushed upwards by ground water pressure, especially after heavy summer rain when the soil is saturated. This can crack or even lift the shell. Pools are usually drained in the dry season, with the ground conditions checked first, and kept empty for as short a time as possible. Fibreglass pools need particular care. If you are thinking of draining a pool to investigate a leak, get advice first.
Local conditions
Pools on clay and sloping ground
Some Pretoria and Johannesburg properties sit on clay soils that swell when wet and shrink in the dry winter. That seasonal movement can stress a pool shell and the joints around fittings, and cracks may open slowly over several years. Pools built on sloping ground, partly in fill, can move differently on each side.
Where cracks keep reappearing, the cause may be structural rather than a simple waterproofing failure, and an engineer’s view may be needed before a new lining is installed.
Tiled pools
Tiles, grout and the membrane underneath
As with showers and balconies, pool tiles and grout are not the waterproof layer. Water that gets through grout or a cracked tile soaks into the bedding, and only a membrane under the tiles stops it reaching the shell. Loose or drummy tiles, grout washing out and staining along joints are signs that water is moving behind the finish. A lasting repair usually means removing the affected tiles, checking the shell and waterproofing before retiling.
Comparing quotes
What an inspection should cover before any quote
- Whether evaporation and plumbing have been ruled out, with the bucket test results.
- Where the water is being lost, with dye-test or other evidence.
- The condition of the shell, the finish, the fittings and the coping.
- How and when the pool will be drained and refilled, and any ground-water precautions.
- The waterproofing product, its suitability for immersion, the number of coats and the finish that goes over it.
- What is excluded, and what guarantee, if any, applies and on what terms.
Next steps
Read more about pool waterproofing, or about home and complex pools on our waterproofing in Johannesburg page. When you are ready, request a quote.
Request a waterproofing quote
Send your suburb, what is leaking and a few photos. We arrange a site visit and set out the work in a written quote.
Request a quote